Posts

Showing posts from June, 2021

WEEK 17 REPORT

Image
For this week, the presentation day for FYP2 was held on 2 June 2021. The assessor for my project was Mr. Ahmad Zuber Conclusion from the presentation: The assessor suggest that for the further research, the prototype need to have the alert system to alert the biomedical personnel if there is the exceeding reading for the temperature and humidity in the imaging room The assessor also suggest that to have the backup plan if there is suddenly power trip in the imaging room and find out the way on how to solve the problem 

WEEK 16 REPORT

Image
For this week, the preparation for the FYP2 presentation was made, by preparing the slide presentation, video demonstration and also video presentation The figure above shows the first slide of slide presentation of this project The figure above shows the image from the video for demonstration  The figure above shows the image from the video for presentation 

WEEK 15 REPORT

Image
For this week, the meeting was conducted with the sv to update the progress of the project The figure above show the date and times of the meeting for the progress update Conclusion from the meeting: Need to overlook the problem related the project Need to collect the data to determined the project will success or not Ask the senior regarding the Lora module

WEEK 14 REPORT

Image
For this week, the data is collected in the simulation room. The data is collected to check on how far the lora can transmit and receive the data.  The figure above shows the transmitter circuit has been place in the simulation room The figure above shows the receiver circuit has been place outside the simulation room The figure above shows that data collected at 12:03 pm The figure above shows that data collected at 3:43 pm Analysis: In the simulation room, the distance that the lora took to transmit and receive data was about 5 meters The temperature and humidity was determined by the temperature and humidity of the air-conditioner There was a lot of disturbance that might be reasons the data being interrupted and cannot receive well, the serial monitor of Arduino IDE need to be on/off for few times to get the reading

WEEK 13 REPORT

Image
For this week, the data is collected at the open space place. The data is collected to check on how far the lora can transmit and receive the data. The figure shows the transmitter circuit has been place in front of the UniKL BMI field The figure shows the receiver circuit has been place in the student lounge The figure above show the reading is taken at 3:00 pm The figure above show the reading is taken at 4:01 pm Analysis: At open space, the distance that the lora took to transmit and receive data was about 60 meters The temperature and humidity was determined by the weather and there was no changes in an hour There was several disturbance that might be reasons the data being interrupted at 4:00 pm

WEEK 12 REPORT

Image
  For this week, for the transmitter circuit, the Lora module is been soldered with the headless pin, to make it easy to connect the Lora with jumper wire. After that, it was connected with Arduino uno and DHT11 to make it a complete circuit   The figure above show the transmitter circuit that has been constructed without the breadboard

WEEK 11 REPORT

Image
For this week, for the receiver circuit, the Lora module is been soldered with the headless pin, to make it easy to connect the Lora with jumper wire. After that, it was connected with Arduino uno to make it a complete circuit   The figure above show the receiver circuit that has been constructed without the breadboard

WEEK 10 REPORT

Image
For this week, there was a meeting with sv, to update the progress of the project The figure above show the date and times for the meeting Conclusion from the meeting Need to collect the data at the lab when the lab can be enter Need to check the internet intermittent at the academic building Recheck the circuit on why the data cannot be collected  

WEEK 9 REPORT

Image
For this week,  there will show on how the temperature and humidity data is been taken for monitoring. The figure above show on how the result is being display on the serial monitor After construct the transmitter and receiver circuit, both of the circuit is been connected to the laptop. The figure above show the result of the temperature and humidity in the room. It is the first data recorded, to make sure the coding upload into both of the circuit is working well.

WEEK 8 REPORT

Image
For this week, there is the explanation why Arduino Uno was choose to be used in this project as microcontroller to process the data. The figure above show the Arduino uno that has been used in this project The  Arduino Uno  is a microcontroller board based on the ATmega328 . It has 14 digital input/output pins (of which 6 can be used as PWM outputs), 6 analog inputs, a 16 MHz ceramic resonator, a USB connection, a power jack, an ICSP header, and a reset button. The Arduino Uno can be powered either by USB or an external power supply. The power source is automatically selected. An AC-to-DC adapter (wall-wart) or a battery can provide external (non-USB) power. A 2.1mm center-positive plug can be plugged into the board's power connector to connect the adapter. Battery leads can be put into the power connector's Gnd and Vin pin headers. The board can be powered from a 6 to 20 volt external supply. If less than 7V is given, the 5V pin may supply fewer than five volts, making ...

WEEK 7 REPORT

Image
For this week, there is the explanation why DHT11 was choose to be used in this project as temperature and humidity sensor. The figure above show the DHT11 that act as temperature and humidity sensor in this project The figure above show the technical specification for DHT11 Based the figure above, DHT11 accuracy for humidity is about +-5% from the actual humidity in the surrounding while +-2% for temperature from the actual temperature in the surrounding. The figure above show the electrical characteristic for DHT11 For DHT11, the power supply is between 3V to 5V while the current supply is between 0.5mA to 2.5mA. If the power supply or current supply is lower than the specification, the DHT11 might not work and if the power supply or current supply is more than the specification, the DHT11 will be burn out and cannot be use.

WEEK 6 REPORT

Image
For this week, there is the explanation why Lora module was choose to be used in this project other than other RF module The figure above show the lora module (SX1278) that has been used in this project The figure above shows the device variants and their key parameters SX1278 frequency range:       The oscillation rate of an alternating electric current or voltage, as well as a magnetic, electric, or electromagnetic field or mechanical system, in the frequency range of 20 kHz to 300 GHz is known as radio frequency. For this lora module, its frequency range is about 137 - 525Mhz. spreading factor The spreading factor controls the chirp rate, and thus controls the speed of data transmission.  Lower spreading factors  mean  faster chirps  and therefore a  higher data transmission rate . For every increase in spreading factor, the chirp sweep rate is halved, and so the data transmission rate is halved. The spreading factor for the lora module is betw...

WEEK 5 REPORT

Image
  For this week, the receiver circuit is constructed by using the, Arduino uno and SX1278 (LoRa module). Since the voltage supply to the SX1278 is less than 5V, the SX1278 is connected to the pin of 3.3V on the Arduino uno. The figure shows the receiver circuit that have been constructed

WEEK 4 REPORT

Image
For this week, the coding for the receiver circuit is being created. The coding will be modified, according to the situation. The original coding will receive the data, in estimation, for every 2 second, from the transmitter circuit. The data that have been collected, will be display on the serial monitor in the Arduino IDE. Both of the figure shows the coding for the transmitter circuit